Code: [Selecteer]Here we are with....FirmWare 1.1.1.:-General:-- DR5000 will go into FW update mode when both STOP and GO buttons are pressed while power to DR5000 is applied- RailCom:-- Added configuration of RailCom cut-out polarity: Negative -> against Ground, Positive -> against V+ (19V) Needed to comply with certain boosters.-- Added Auto Cut-out polarity: When operating with a reverse-loop booster (like DR5033) DR5000 will switch it's Cut-out polarity automaticcally when detecting a different booster polarity.-- Enabled POM-read commands, so that decoder responses to the POM read can be read by external RailCom detectors-XpressNet:-- Report correct speedsteps to MultiMaus- and LH controllers is loco is selected for the first time.-- Fixed translation of 14 and 28 speedstep speeds to match 128 speedstep speeds; ( 14-18 Step 1 was step 22 at 128 Step, now 14-28 Step 1 is now Step 1 at 128 Step.-- Fixed 'Report feedback' command to report Feedback and not Turnout status. Status requests for module >= "Feedback base module" are reported as Feedback, below that Turnouts are reported (as of Lenz spec's)-- Enabled 'Report contacts at power-on' for FB-Bus modules-- Implemented Special option for WDP to broadcast Loco Speed- and Fucntion info when Loco is controlled by external device. (USB and LAN connections only)-LocoNet-- Implemented "Dispatch" functionality-- Implemented "Program Track" functionality-- Implemented "Fast Clock" functionality-- Implemented Turnout 1016 - 1019 commands for interrogating Feedback Contacts-- Implemented Uhlenbrock(r) special commands for interrogating Feedback Contacts-- Implemented LNCV programming-- Added special option for using (somewhat slower) FRED devices, adjusts the timing of certain replies -- Added special option to tune the Baudrate of the LocoNet. Some small LocoNet devices with 'bit-bang' transmitters and receivers sometimes are off-spec (16.66KBaud) and need slightly higer or lower Baudrate.-- Added special option for Comparator levels. In case of large, heavilly loaded LocoNets, Signal edges may deteriote an become slower, causing incorrect startbit recognition.-- Relaxed startbit sampling to prevent false 'negatives' due to slow edges on large LocoNets.-- Fixed problem with OPC_IDLE causing the DR5000 to hang (Traincontroller, WDP and iTrain) when putting the layout in 'Freeze' ('Einfrieren') mode.Config App 1.1.1.- LAN/WiFi-- Implemented DR5000 discovery, so the Config App will show all DR5000's on the network connected to the controlling PC. IP's are shown in combobox for easy selection.- ext88N-- Feedback monitor now shows colorized overlaps in DR5000 feedback space- LocoNet-T-- Added LNCV programming page-- Added Feedback monitor which shows colorized overlaps in DR5000 feedback space-- Added Settings page with: + Purge time --> Time in minutes when to purge IDLE slots (not effective yet in FW 1.1.1.) + FastClock rate --> Set the rate at which the clock ticks compared to realtime. + Enable special FRED timing --> Enable special timing for (Uhlenbrock(r) FREDs. + Baudrate tuning --> Adjust LocoNet baudrate from -1000 to + 1000 Baud + Compator tuning --> Adjust '0' bit recognition voltage level- LocoNet-B-- See LocoNet-T-- Added LNCV capable Booster monitor (DR5033 only for now)- Track Output-- Added RailCom cut-out polarity (see firmware description)-- Added Auto cut-out polarity (see firmware description)- XN+FB Bus-- Added special option "Enable Loco Info broadcast" for WDP ( or other control programs which can handle this. It eliminates the need for the notorious Lenz protocol specific polling for Loco Info.-- Feedback monitor now shows colorized overlaps in DR5000 feedback space-Prog Track-- CV Read button now enabled for POM when in 'Track-out' RailCom cut-out is enabled.-USB 2.0-- Implemented automatic insertion and removal of the DR5000 USB cable. (feature is still under development, may crash sometimes upon removal)That's all (32 updates !!) Folks :)
Here we are with....FirmWare 1.1.1.:-General:-- DR5000 will go into FW update mode when both STOP and GO buttons are pressed while power to DR5000 is applied- RailCom:-- Added configuration of RailCom cut-out polarity: Negative -> against Ground, Positive -> against V+ (19V) Needed to comply with certain boosters.-- Added Auto Cut-out polarity: When operating with a reverse-loop booster (like DR5033) DR5000 will switch it's Cut-out polarity automaticcally when detecting a different booster polarity.-- Enabled POM-read commands, so that decoder responses to the POM read can be read by external RailCom detectors-XpressNet:-- Report correct speedsteps to MultiMaus- and LH controllers is loco is selected for the first time.-- Fixed translation of 14 and 28 speedstep speeds to match 128 speedstep speeds; ( 14-18 Step 1 was step 22 at 128 Step, now 14-28 Step 1 is now Step 1 at 128 Step.-- Fixed 'Report feedback' command to report Feedback and not Turnout status. Status requests for module >= "Feedback base module" are reported as Feedback, below that Turnouts are reported (as of Lenz spec's)-- Enabled 'Report contacts at power-on' for FB-Bus modules-- Implemented Special option for WDP to broadcast Loco Speed- and Fucntion info when Loco is controlled by external device. (USB and LAN connections only)-LocoNet-- Implemented "Dispatch" functionality-- Implemented "Program Track" functionality-- Implemented "Fast Clock" functionality-- Implemented Turnout 1016 - 1019 commands for interrogating Feedback Contacts-- Implemented Uhlenbrock(r) special commands for interrogating Feedback Contacts-- Implemented LNCV programming-- Added special option for using (somewhat slower) FRED devices, adjusts the timing of certain replies -- Added special option to tune the Baudrate of the LocoNet. Some small LocoNet devices with 'bit-bang' transmitters and receivers sometimes are off-spec (16.66KBaud) and need slightly higer or lower Baudrate.-- Added special option for Comparator levels. In case of large, heavilly loaded LocoNets, Signal edges may deteriote an become slower, causing incorrect startbit recognition.-- Relaxed startbit sampling to prevent false 'negatives' due to slow edges on large LocoNets.-- Fixed problem with OPC_IDLE causing the DR5000 to hang (Traincontroller, WDP and iTrain) when putting the layout in 'Freeze' ('Einfrieren') mode.Config App 1.1.1.- LAN/WiFi-- Implemented DR5000 discovery, so the Config App will show all DR5000's on the network connected to the controlling PC. IP's are shown in combobox for easy selection.- ext88N-- Feedback monitor now shows colorized overlaps in DR5000 feedback space- LocoNet-T-- Added LNCV programming page-- Added Feedback monitor which shows colorized overlaps in DR5000 feedback space-- Added Settings page with: + Purge time --> Time in minutes when to purge IDLE slots (not effective yet in FW 1.1.1.) + FastClock rate --> Set the rate at which the clock ticks compared to realtime. + Enable special FRED timing --> Enable special timing for (Uhlenbrock(r) FREDs. + Baudrate tuning --> Adjust LocoNet baudrate from -1000 to + 1000 Baud + Compator tuning --> Adjust '0' bit recognition voltage level- LocoNet-B-- See LocoNet-T-- Added LNCV capable Booster monitor (DR5033 only for now)- Track Output-- Added RailCom cut-out polarity (see firmware description)-- Added Auto cut-out polarity (see firmware description)- XN+FB Bus-- Added special option "Enable Loco Info broadcast" for WDP ( or other control programs which can handle this. It eliminates the need for the notorious Lenz protocol specific polling for Loco Info.-- Feedback monitor now shows colorized overlaps in DR5000 feedback space-Prog Track-- CV Read button now enabled for POM when in 'Track-out' RailCom cut-out is enabled.-USB 2.0-- Implemented automatic insertion and removal of the DR5000 USB cable. (feature is still under development, may crash sometimes upon removal)That's all (32 updates !!) Folks :)
Nee, dat gaat niet.
Print
